Short-wave and fast medium-wave IR heaters

The QSM is an IR -heating element consisting of one or more primary radiators as Infrared heating elements located in a hermetically sealed outer round quartz tube, the secondary chamber. Each chamber is filled with the atmosphere most suitable for it.

The QSM is mainly used for heating a room or in furnace construction. In the version with a lead end on one side, the QSM can also be used as an immersion heater in liquids. If the IR radiation is to be directed, it is recommended to use an external reflector or gold reflector. The external melting must not exceed 350°C when operating in a normal atmosphere. Use in a vacuum is also possible without any problems.

The switch-on time of the QSM is approx. 3 seconds to reach the operating state.

The following are eligible

• Heating power in combination with the supply voltage
• Heating length up to 2 metres
• Emission maximum of the emitted IR radiation between 1,8 μm - 2,8 μm.
• Energiedichte bezogen auf die Heizlänge beträgt bis zu 50W/cm.

We have a wide range of standard products. We will be happy to assist you in selecting the most suitable IR radiant heater for your heating task. Please do not hesitate to contact us.

The following table shows the standard types QSM in different versions. They differ in the number of primary radiators and the quartz tube cross-section.

Advantages

• Multi-chamber system hermetically sealed to the outside
• Increased safety due to the multi-chamber system
• High durability
• Kurze Ansprechzeit von ca. 3 Sekunden
• Infinitely variable 0-100%
• High efficiency through adjustment of the emission maximum
• Contactless heat transfer
• Can be used in vacuum
• Suitable for cleanroom
• Emission-free
• Resistant to acidic and basic substances (with the exception of hydrofluoric and phosphoric acid)
• Very low heat expansion
• High thermal shock resistance

Options

• Lead ends on both sides (Z)
• Switchable heating zones
• Customised assembly of the lead ends and contacts
• Angled outer fusion (90°)
• Ceramic end (K)
• Shrink tubing (S)

The FQSM is an IR -heating element consisting of one or more primary radiators as Infrared heating elements, which together with an integrated reflector is located in a hermetically sealed outer quartz flat tube, the secondary chamber. Each chamber is filled with the atmosphere best suited to it.

The FQSM is particularly suitable for heating a surface or a band. Due to the integrated reflector, the IR radiation is already directed and hits where it is needed for heating. The external melting must not exceed 350°C in operation under normal atmosphere. Use in a vacuum is also possible without any problems.

The switch-on time of the FQSM is approx. 3 seconds to reach the operating state.

The following are eligible

• Heating length up to 2 metres
• Heating power in combination with the supply voltage
• Emission maximum of the emitted IR radiation between 1,8 μm - 2,8 μm.
• Energy density in relation to the heating length up to 50 W/cm.

We have a wide range of standard products. We are happy to assist you in selecting the most suitable IR heater for your heating task. Please do not hesitate to contact us.

The following table shows the standard types of FQSM in different versions. They differ in the number of primary radiators.

Advantages

• Multi-chamber system hermetically sealed to the outside
• Directed IR radiation through integrated reflector
• Integrated reflector in its own protective gas medium
• Integrated reflector that cannot be negatively influenced from the outside
• Increased safety due to the multi-chamber system
• High durability
• Kurze Ansprechzeit von ca. 3 Sekunden
• Infinitely variable 0-100%
• High efficiency through adjustment of the emission maximum
• Contactless heat transfer
• Can be used in vacuum
• Suitable for cleanroom
• Emission-free
• Resistant to acidic and basic substances (with the exception of hydrofluoric and phosphoric acid)
• Very low heat expansion
• High thermal shock resistance

Options

• Lead ends on both sides (Z)
• Switchable heating zones
• Customised assembly of the lead ends and contacts
• Angled outer fusion (90°)
• Ceramic end (K)
• Cable bend relief (T)

The FQHS is an IR-heating element consisting of one or more primary radiators as IR-emitters, which together with an integrated reflector is located in a hermetically sealed outer quartz flat tube, the secondary chamber. Each chamber is filled with the atmosphere most suitable for it.

The FQHS is particularly suitable for heating a surface or a band. Due to the integrated reflector, the IR radiation is already directed and hits where it is needed for heating. The external melting must not exceed 350°C in operation under normal atmosphere. Use in a vacuum is also possible without any problems.

The switch-on time of the FQHS is approx. 1 second to reach the operating state.

The following are eligible

• Heating length up to 2 metres
• Heating power in combination with the supply voltage
• Emission maximum of the emitted IR radiation between 1,0 μm - 2,8 μm.
• Energy density in relation to the heating length up to 120W/cm.

We have a wide range of standard products. We will be happy to assist you in selecting the most suitable IR-heater for your heating task. Please do not hesitate to contact us.

The following table shows the standard types FQHS in different versions. They differ in the number of primary radiators, the radiation angle and the quartz cross-section.

Advantages

• Multi-chamber system hermetically sealed to the outside
• Directed IR radiation through integrated reflector
• High efficiency due to adjustment of the radiation direction
• Integrated reflector in its own protective gas medium
• Integrated reflector that cannot be negatively influenced from the outside
• Increased safety due to the multi-chamber system
• High durability
• Very short response time of approx. 1 second
• Infinitely variable 0-100%
• High efficiency through adjustment of the emission maximum
• Contactless heat transfer
• Can be used in vacuum
• Suitable for cleanroom
• Emission-free
• Resistant to acidic and basic substances (with the exception of hydrofluoric and phosphoric acid)
• Very low heat expansion
• High thermal shock resistance

Options

• Lead ends on both sides (Z)
• Switchable heating zones
• Customised assembly of the lead ends and contacts
• Angled outer fusion (90°)
• Ceramic end (K)
• Cable bend relief (T)
• Radiation filter in visible light range (F)

The QHS is an IR-heating element consisting of one or more primary radiators as Infrared heating elements located in a hermetically sealed outer quartz round tube, the secondary chamber. Each chamber is filled with the atmosphere most suitable for it.

The QHS is mainly used for heating a room, such as a roller from the inside or in oven construction. In QHS version with a lead end on one side can also be used as an immersion heater in liquids. The QHS-R version with integrated reflector turns the standard QHS-S into an area radiator. If the IR radiation is to be directed elsewhere, it is recommended to use an external reflector. The external fusion must not exceed 350°C when operating in a normal atmosphere. Use in a vacuum is also possible without any problems.

The switch-on time of the QHS is approx. 1 second to reach the operating state.

The following are eligible

• Heating power in combination with the supply voltage
• Heating length up to 2 metres
• Emission maximum of the emitted IR radiation between 1,0 μm - 2,8 μm.
• Energiedichte bezogen auf die Heizlänge beträgt bis zu 150W/cm.

We have a wide range of standard products. We will be happy to assist you in selecting the most suitable IR radiant heater for your heating task. Please do not hesitate to contact us.

The following table shows the standard types QHS in different versions. They differ in the number of primary radiators, the radiation angle and the quartz tube cross-section.

Advantages

• Multi-chamber system hermetically sealed to the outside
• Directed IR radiation through integrated reflector (nur QHS-R)
• High efficiency due to adjustment of the radiation direction (nur QHS-R)
• Integrated reflector in its own protective gas medium (nur QHS-R)
• Integrated reflector that cannot be negatively influenced from the outside (nur QHS-R)
• Increased safety due to the multi-chamber system
• High durability
• Very short response time of approx. 1 second
• Infinitely variable 0-100%
• High efficiency through adjustment of the emission maximum
• Contactless heat transfer
• Can be used in vacuum
• Suitable for cleanroom
• Emission-free
• Resistant to acidic and basic substances (with the exception of hydrofluoric and phosphoric acid)
• Very low heat expansion
• High thermal shock resistance

Options

• Lead ends on both sides (Z)
• Switchable heating zones
• Customised assembly of the lead ends and contacts
• Angled outer fusion (90°)
• Ceramic end (K)
• Shrink tubing (S)
• Cable bend relief (T)
• Handle (H)
• Damping stop (A)
• Radiation filter in visible light range (F)

The HH consists of a heating coil made of high-temperature melting metal, the most suitable atmosphere for this and quartz glass as an envelope. This heating coil is heated by means of electrical energy and emits radiation in the infrared range with emission maxima of 1.0 μm - 2.8 μm. The efficiency of the conversion of electrical energy to IR radiation energy is up to 90% here.

The HH is primarily to be used for heating a room. If the IR radiation is to be directed, it is recommended to use an external reflector. The external meltdown must not exceed 350°C when operating in a normal atmosphere.

The switch-on time of the HH is approx. 1 second to reach the operating state.

The following are eligible

• Heating power in combination with the supply voltage
• Die Heizlänge bis zu 0,7 Meter
• Emission maximum of the emitted IR radiation between 1,0 μm - 2,8 μm.
• Energiedichte bezogen auf die Heizlänge beträgt bis zu 50W/cm.

We have a wide range of standard products. We will be happy to assist you in selecting the most suitable IR radiant heater for your heating task. Please do not hesitate to contact us.

The following table shows the standard type HH.

Advantages

• Very short response time of approx. 1 second
• Infinitely variable 0-100%
• High efficiency through adjustment of the emission maximum
• Contactless heat transfer
• Emission-free
• Very low heat expansion
• High thermal shock resistance

Options

• Customised assembly of the lead ends and contacts
• Ceramic end (K)
• Cable bend relief (T)
• Radiation filter in visible light range (F)

The SHS consists of a heating coil made of high-temperature melting metal, the most suitable atmosphere for this and quartz glass as an envelope. This heating coil is heated by electrical energy and emits radiation in the infrared range with emission maxima of 0.8 μm - 2.8 μm. The efficiency of the conversion of electrical energy to IR radiation energy is up to 90% here.

The SHS is primarily to be used for heating a room. If the IR radiation is to be directed, it is recommended to use an external reflector. With the option of a gold reflector, which is located on the quartz glass, one obtains irradiation of a small area, such as is required for heating individual electronic components. The external melting must not exceed 350°C in operation under normal atmosphere.

The switch-on time of the SHS is approx. 1 second to reach the operating state.

The following are eligible

• Heating power in combination with the supply voltage von 0 – 30V
• Emission maximum of the emitted IR radiation between 0,8 μm - 2,8 μm.
• Energiedichte bezogen auf die Heizlänge beträgt bis zu 250W/cm.

We have a wide range of standard products. We will be happy to assist you in selecting the most suitable IR radiant heater for your heating task. Please do not hesitate to contact us.

The following table shows the standard type SHS.

Advantages

• Very short response time of approx. 1 second
• Infinitely variable 0-100%
• High efficiency through adjustment of the emission maximum
• Contactless heat transfer
• Emission-free
• Very low heat expansion
• High thermal shock resistance

Options

• gold reflector